How to Install a Wall Mount Can Crusher (Step-by-Step)

A wall mount can crusher only works as well as it's installed. Mount it too low and you end up bending over and pushing with your arms. Mount it into drywall alone and the whole unit wobbles every time you pull the handle. Get the installation right and crushing a can, a 2-liter bottle, or even a gallon jug becomes one easy, smooth pull. This step-by-step guide walks you through installing a wall-mounted crusher like the BIG CAN CRUSHER, from picking the spot to the first test crush.
What You'll Need
Installation is a short, simple job. The BIG CAN CRUSHER comes fully assembled with all mounting hardware included, so you don't need to put the crusher itself together. Most people finish in about 10 minutes. Have these on hand:
- A drill/driver with a bit sized for pilot holes
- A stud finder (or another way to locate studs)
- A pencil for marking holes
- A level, to keep the crusher straight
- A tape measure
- The included mounting hardware
If you're mounting onto masonry, brick, or concrete instead of wood, you'll need anchors and fasteners rated for that material, plus a masonry bit.
Step 1: Choose the Right Location
Think about where your empties pile up. The best spot is where you already open, drink, and toss containers, so crushing becomes part of the routine instead of an extra chore. Popular places include:
- Garage: close to the recycling cart, with plenty of room to swing the handle.
- Kitchen or pantry: right next to the recycling bin.
- Utility or laundry room: out of sight but easy to reach.
- Workshop, bar, or rental property: anywhere cans and bottles collect quickly.
Make sure there's clear space in front of and below the crusher for the handle to travel all the way down, and room for a bin underneath or beside it so flattened containers drop straight in.
Step 2: Find a Stud or Solid Wood
This is the step that makes the biggest difference in how the crusher feels. Every pull puts force on the mounting point, and drywall by itself isn't designed to hold that kind of repeated load. For the most solid feel, mount the crusher into a wall stud or solid wood.
Use a stud finder to locate a stud and mark its center. In many garages the studs are exposed, which makes this even easier. If there's no stud exactly where you want the crusher, a common solution is to fasten a sturdy piece of wood (a backer board) across two studs first, then mount the crusher onto that board.
Before drilling anywhere, check that there are no electrical wires or plumbing pipes behind that part of the wall.
Step 3: Set the Mounting Height
Height is the detail most people get wrong. A wall-mounted crusher works on leverage, and you get the most from it when you can pull down using your body weight rather than only your arm muscles.
A good rule: mount the crusher so the top of the raised handle sits around chest-to-shoulder height for the person who will use it most. Hold the crusher against the wall, raise the handle, and check where it lands before you mark anything. If several people will use it, aim for a height that's comfortable for the shortest regular user.
Step 4: Mark and Drill Pilot Holes
Hold the mounting plate against the wall at your chosen height, centered on the stud or backer board. Use a level to make sure it's straight, then mark the screw holes with a pencil.
Set the crusher aside and drill pilot holes at your marks. Pilot holes make the screws go in straight, reduce the chance of splitting the wood, and help the screws bite firmly.
Step 5: Screw the Crusher to the Wall
Line the mounting plate up with the pilot holes and drive in the included screws. Tighten them until the plate sits flat and firm against the wall, without stripping the holes.
Give the crusher a firm tug in every direction. It shouldn't shift, rock, or flex away from the wall. If it moves, check that the screws are actually in the stud or solid wood, and tighten them.
Step 6: Do a Test Crush
Start with an empty 12 oz aluminum can. Raise the handle, set the can in the chamber, and pull the handle down in one smooth motion. Then move up to bigger containers. Because the chamber is sized for 1-gallon jugs, the BIG CAN CRUSHER also handles 16.9 oz water bottles, 2-liter soda bottles, and gallon milk or water jugs.
For plastic bottles and jugs, always remove the cap first and squeeze out some of the air. A capped bottle traps air, pushes back against the handle, and can pop. Uncapped, a 2-liter bottle flattens in a single stroke. For more detail, see our guides on how to crush 2-liter bottles for recycling and how to crush a gallon milk jug.
Common Installation Mistakes
Mounting into drywall only
Drywall alone can loosen or crack over time under repeated pulls. Use a stud, solid wood, or a backer board.
Mounting too low
A low crusher forces you to push with your arms and back. Mount it so the raised handle reaches chest-to-shoulder height.
No room for the handle or bin
Cabinets, shelves, or a car parked too close can block the handle's path. Leave clear space for the full stroke and a bin underneath.
Skipping pilot holes
Driving screws straight into wood without pilot holes can split the wood or leave screws crooked and loose.
Maintenance After Installation
Any lever tool gets a lot of force through its hardware. After the first few weeks of use, check that the mounting screws and the pivot bolt are still snug, and tighten them if needed. After that, an occasional check is enough. Because the BIG CAN CRUSHER's body, handle, and hardware are all metal, with no plastic hinge or plastic structural parts, there's very little else to maintain. If you're comparing models, our guide to the best wall mount can crusher in 2026 covers what to look for.
Frequently Asked Questions
How long does it take to install a wall mount can crusher?
For the BIG CAN CRUSHER, about 10 minutes. It comes fully assembled with all mounting hardware included: drill pilot holes, line up the mounting plate, and screw it in.
Can I mount a can crusher on drywall?
Not on drywall alone. Mount it into a wall stud or solid wood, or attach a wooden backer board across studs and mount the crusher onto the board.
How high should I mount my can crusher?
Position it so the top of the raised handle sits around chest-to-shoulder height. That lets you use your body weight for an easy pull.
Can I install it on brick or concrete?
Yes, with anchors and fasteners rated for masonry and a masonry drill bit, since standard wood screws won't hold in those materials.
Will a wall-mounted crusher handle 2-liter bottles and gallon jugs?
Many can crushers are built only for 12 oz cans. The BIG CAN CRUSHER's chamber is sized for 1-gallon jugs, so it crushes 2-liter bottles and gallon jugs as well as cans and water bottles. Remove caps first.
Does it need any maintenance?
Just check the mounting screws and pivot bolt after the first few weeks and tighten them if needed. You'll find more answers on our FAQ page.
Ready to Mount Yours?
A solid, well-placed installation turns crushing into a two-second habit and keeps your recycling bin from overflowing. The BIG CAN CRUSHER arrives fully assembled with the hardware you need, is built from heavy-duty steel, and handles everything from 12 oz cans to gallon jugs. Every order comes with a 30-day money-back guarantee.
Crush gallon jugs, 2-liter bottles & cans in one pull
See the BIG CAN CRUSHER